This site uses cookies to improve your experience. They are safe and secure and never contain sensitive information. For more information click here.

Bircher ClickLine Safety Edges

Idea Safety Edges for Automatic Platforms, Swing Gates & Industrial Doors
ClickLine Safety Edges are suitable for automatic
Product Info

Our Bircher ClickLine Safety Edges are available in a number of different sizes from 25 mm to 65 mm high from the C-Channel.  The “Click” foot of the safety edge makes installation of the profiles a simple task of clipping them in from the side of the profile.

QTY Price ex VAT
Price ex VAT

in stock

QTY Price ex VAT
Price ex VAT

in stock

Safety edges, safety ribs, bump strips are just a few of the names used to describe these safety products.  No matter what you call them, they all do the same job of protecting dangerous crush and shear points on platforms, tables, gates and doors.

Bircher safety edges comprise three elements:

  1. The aluminium mounting rail, which is C-Shaped for ClickLine safety edges is fitted to the device you want to protect.  Important, please make sure that the fixing heads of the screws used do not press on the rear of the safety edge as this will give you false triggers.
  2. The rubber profile, this is the external part of the safety edge that holds the switching strip in position and depending on the size of the profile will determine the all-important over travel distance.  Typically, the bigger the profile the larger the over travel figure and the greater the protection.  Important, please check the figures below to choose the correct profile for your application.
  3. The switching strip or contact strip, this is the heart of the edge which when compressed provides the signal to the switching or safety units to show when the edge has been activated.

Safety edges are manufactured in two formats a “pass through” or “link” version with two cables and the “end-of-line” version with 8k2 terminating resistors.  Up to four edges (as recommended by Bircher) can be are wired together in series with each other with the 8k2 version being the last link in the chain.  The switching unit monitors the resistance of the series of safety edges, if any of the edges in the chain are compressed this will cause the safety relays on the switching unit to open, also if any of the cables in the circuit are damaged the unit will show this as a fault and the safety relays will be opened.

All our safety edges are manufactured to order at Motion29, typically in 1 to 2 days from receipt of your order.  While we have fixed sizes available via our website, we manufacture all edges to order and it is no problem to make them to the size that you require, so please give us a call on 01495 360022 if you cannot find the size you need.

Over Travel Figures:

ELE025/029A0V – 250N = 8 mm, 400N = 10 mm

ELE030/042A0V – 250N = 18 mm, 400N = 20 mm

ELE036/045A0V – 250N = 21 mm, 400N = 22 mm

ELE036/065A0V – 250N = 21 mm, 400N = 25 mm

Lipped Profiles:

ELE030/042J2V – 250N = 5 mm, 400N = 14 mm

ELE036/045J2V – 250N = 17 mm, 400N = 20 mm

Installation: ClickLine safety edges should be clicked into the C-Channel using a rocking motion.  Pulling or sliding the profile into the channel may result in damage to the mounting foot and invalidate the warranty.  Ensure the edge is flush with the mounting channel and the heads of the fixing screws are not pushing on the rear of the profile as both can provide false readings from the safety edges.  If you are not sure, please contact us for advice on 01495 360022.

 

It is important that the correct profile is used as the type, size and speed of your automatic system (platform, door, gate, etc.) all influence the stopping distance and the force testing results set out in the standards.

Standard Profiles:

ELE025/029A0V – 250N = 8 mm, 400N = 10 mm

ELE030/042A0V – 250N = 18 mm, 400N = 20 mm

ELE036/045A0V – 250N = 21 mm, 400N = 22 mm

ELE036/065A0V – 250N = 21 mm, 400N = 25 mm

Lipped Profiles:

ELE030/042J2V – 250N = 5 mm, 400N = 14 mm

ELE036/045J2V – 250N = 17 mm, 400N = 20 mm

 

 

Featured Products
ESGate Electronic Switching Units for Safety Edges featured

ESGate Switching Units

The ESGate safety switching units are designed for evaluating safety edges and safety mats. The ESGate 2 is a category 2 device with external test input, whereas the ESGate 3 is a category 3 self-monitored device.

ESD3 Switching Units for Safety Edges featured

ESD3 Switching Units

These are ideal for monitoring safety edges and mats in machine safety applications as they offer the choice of manual or automatic reset.

Switching units for safety edges and safety mats. featured

Wired Switching Units

The MsMatrix 3, ESGate 2 & 3 or the ESD3 series of switching units are suitable for monitoring directly wired safety mats and safety edges in gate, door and machine applications.  They provide a simple to use solution for monitoring the 8k2 resistor used in safety edges & mats.

Contact Details
Motion29 Limited
Unit C9 Block C, Newbridge Road Industrial Estate
Pontllanfraith
Blackwood
NP12 2XF
Tel: 01495 360022
Fax: 01495 227727
© 2018 Motion29 Limited